EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Instrukcja Obsługi Strona 39
- Strona / 64
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Instruction Manual CyberScan pH 1100/ 2100
39
10.3.3 mV calibration due alarm setup program P2.1
Use this program to set a reminder when the next calibration is
due. Choose from 1 to 365 days from last calibration.
1. Enter mV setup mode as described in steps 1-4 in Section
10.3.1 Entering mV setup mode (page 37).
2. Use ∆/MI key to scroll to program mVCalDue Alarm: P2.1.
See Figure 116.
3. Press ENTER to enter program mVCalDue Alarm: P2.1.
4. Press >/CAL to toggle between Cal Alarm Due:On and Off.
The selection will flash. See Figure 117.
5. Press ENTER to confirm selection.
• If you selected On, continue to step 6.
• If you select Off, pressing ENTER returns to the setup
mode.
Press ∆/MI to continue to the next setup program, or press
∇/MR to go to the previous program. Press EXIT to return to
mV measurement mode.
6. If you selected On in step 5, the display reads Key in Cal
Due Period (1-365 days) =. Key number of days using the
numeric keypad. If you make a mistake, use the ∆/MI or
∇/MR keys to highlight mistake, then re-enter.
See Figure 118.
7. Press ENTER to confirm number of days to next calibration,
screen flashes Sys Updating, Please wait... and returns to
the setup mode.
Press ∆/MI to continue to the next setup program, or press
∇/MR to go to the previous program. Press EXIT to return to
mV measurement mode.
Keyin Cal Due Period
(1-365 days) = 1
Cal Alarm Due On Off
Select & Press ENTER
mVCalDue Alarm :P2.1
Press ENT. to Select
Figure 116
Figure 117
Figure 118
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
(4 strony)
Pomiary, testowanie i kontrola EUTECH INSTRUMENTS ALPHA CON 500 2-WIRE TRANSMITTER Instrukcje Operacyjne
(34 strony)
(34 strony)
Pomiary, testowanie i kontrola EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Instrukcja Obsługi
(20 strony)
(20 strony)
Pomiary, testowanie i kontrola EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Instrukcja Obsługi
(24 strony)
(24 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji