EUTECH INSTRUMENTS ALPHA COND 500 - REV 4 Dokumentacja Strona 52
- Strona / 64
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Transmitter Cond/Res 2-Channel M300 52
© 05/07 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Cond/Res 2-Channel M300
Printed in Switzerland 52 121 318
When Calibrate Meter is selected, the display will show Channel A and Resistance 1, designat-
ing that the transmitter is ready to calibrate the first range resistor on channel A. This resistance
may be changed, selecting range 1 thru 5, or temperature. Each resistance range consists of a
two-point calibration. The temperature calibration consists of a three-point calibration (see table
for temperature resistance values)
Press [ENTER] to begin the calibration process.
The first text line will ask for the Point 1 resistance value (this will correspond to Resistance 1
value shown on the Calibration Module Accessory). The second text line will show the measured
resistance value. When the value stabilizes, press [ENTER] to perform calibration.
The transmitter screen will then prompt the user to enter the value for Point 2, and R1 will dis-
play the measured resistance value. When this value stabilizes, press [ENTER] to calibrate this
range.
Once point 1 and 2 are calibrated, return to the Calibrate Meter screen. Move the cursor to
change Channel A to Resistance 2, designating the second calibration range. Proceed with the
two-point calibration process as performed for the first range. This same process must be fol-
lowed to complete the re-sistance calibration of all 5 ranges.
Next, return to the Calibrate Meter screen and choose Temperature calibration for Channel A,
as shown.
Press [ENTER] to begin temperature calibration process
The first text line will ask for the Point 1 temperature resistance value (this will correspond to
Temperature 1 value shown on the Calibration Module Accessory). The second text line will
show the measured resistance value. When THE value stabilizes, press [ENTER] to perform
calibration.
The transmitter screen will then prompt the user to enter the value for Point 2, and T2 will display
the measured resistance value. When this value stabilizes, press [ENTER] to calibrate this
range.
Repeat these steps for Point 3.
- Operation Manual 1
- Conductivity/Resisitivity 1
- 2-Channel 1
- Transmitter M300 1
- 1 Introduction 7
- 2 Safety instructions 7
- 3 Unit overview 9
- 3.3 Control/Navigation Keys 11
- 3.3.6 “Save changes” dialog 13
- 3.3.7 Security Passwords 13
- 3.4 Display 13
- 4 Installation instruction 14
- 2 Terminal for sensor 19
- 4.3 Connector PIN definition 20
- 6 Quick Setup 21
- 6.3 Measurement Units 22
- 6.4 Analog Outputs 22
- 6.5 Setpoint 23
- 7 Sensor Calibration 24
- 7.5 Sensor Verification 27
- 8 Configuration 28
- 8.2.1 Channel Setup 29
- 8.2.2 Temperature Source 29
- 8.2.4 Set Averaging 31
- 8.3 Analog Outputs 31
- 8.4 Setpoints 33
- 8.5 Alarm/Clean 36
- 8.5.1 Alarm 36
- 8.5.2 Clean 37
- 8.6 Display 37
- 8.6.1 Measurement 37
- 8.6.2 Resolution 38
- 8.6.3 Backlight 38
- 8.6.4 Name 38
- 8.7 Hold Analog Outputs 39
- 9 System 40
- 9.3 Passwords 41
- 9.3.1 Changing Passwords 41
- 9.4 Set/Clear Lockout 41
- 9.5 Reset 42
- 9.5.1 Reset System 42
- 10 PID Setup 43
- 10.1 Enter PID Setup 44
- 10.2 PID Auto/Manual 44
- 10.3 Mode 45
- 10.3.1 PID Mode 45
- 10.4 Tune Parameters 45
- 10.4.3 Proportional Limits 46
- 10.4.4 Corner Points 46
- 10.5 PID Operation 46
- 11 Service 47
- 11.1.2 Digital Input 48
- 11.1.3 Display 48
- 11.1.4 Keypad 48
- 11.1.5 Memory 49
- 11.1.6 Set Relay 49
- 11.1.7 Read Relays 49
- 11.1.8 Set Analog Outputs 50
- 11.1.9 Read Analog Outputs 50
- 11.2 Calibrate 51
- 11.2.1 Calibrate Meter 51
- 11.2.2 Calibrate Analog 53
- 11.2.3 Calibrate Unlock 54
- 11.3 Tech Service 54
- 12 Info 55
- 12.2 Calibration Data 56
- 12.3 Model/Software Revision 56
- 13 Maintenance 57
- 14 Troubleshooting 57
- 14.1 Changing the Fuse 58
- 16 Specifications 59
- 17 Default tables 61
- 18 Waranty 62
- 19 UL Statement (Pending) 62
- Addresses 64
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola EUTECH INSTRUMENTS ALPHA COND 500 - REV 4
Pomiary, testowanie i kontrola EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Instrukcja Obsługi
(64 strony)
(64 strony)
(4 strony)
Pomiary, testowanie i kontrola EUTECH INSTRUMENTS ALPHA CON 500 2-WIRE TRANSMITTER Instrukcje Operacyjne
(34 strony)
(34 strony)
Pomiary, testowanie i kontrola EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Instrukcja Obsługi
(20 strony)
(20 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji